COMPAQ PRESARIO F700 COPROCESSOR DRIVERS

Operating and Performance Specifications Chapter 1. Carefully slide the monitor enclosure away from the power supply subsystem until the enclosure clears the tab in the back corner of the monitor. Page 17 Chapter 3. Page 71 Slide the fuse box back into place. Compaq evo notebook nc series and evo notebook nc series software guide 85 pages.

Uploader: Samucage
Date Added: 4 January 2015
File Size: 69.26 Mb
Operating Systems: Windows NT/2000/XP/2003/2003/7/8/10 MacOS 10/X
Downloads: 42935
Price: Free* [*Free Regsitration Required]

Page display unit. Page 13 system board between the expansion slots, is visible.

Carefully slide the monitor compaq presario f700 coprocessor away from the power supply subsystem until the enclosure clears the tab in the back corner of the monitor. Page 54 Disconnect any peripheral devices printer, monitors, and so on from the computer.

Remove the power switch filter assembly.

To replace the power supply assembly, reverse Steps 1 through 7. Page 18 Chapter 4.

COMPAQ MAINTENANCE AND SERVICE MANUAL Pdf Download.

Enter text from picture: Page 83 Computers on the system board. Compaq Computer Corporation shall not be liable for technical compaq presario f700 coprocessor editorial errors or omissions contained herein; nor for incidental or consequential damages resulting from the furnishing, performance, or use of this material.

During the 90 day ninety day warranty period, Compaq will repair or replace.

Average Access Time Data Transfer Rate 10 Megabyte Tape Drive Specifications Dimensions: Lift the power switch filter assembly out and place it on the chassis Figure 7. Complete the removal procedures for all installed controller and option boards see Section 7. If Enclosure B contains a fixed disk drive, disconnect the compaq presario f700 coprocessor disk drive LED connector from the front of the enclosure and remove this enclosure from the system compaq presario f700 coprocessor Figure 7.

To replace the power switch filter assembly, reverse Steps 1 through 5. To remove the fixed disk drive controller board: Compaq Computer Corporation Compaq warrants the products that it. Determine the configuration compaq presario f700 coprocessor the mass storage devices.

Check this display to make sure it is not tilted in any way. The memory error code points to a specific memory address. Page 80 Remove the retaining screw that secures the video display controller board and disconnects the video display signal cable Figure 7. Page Table 8. Jumper Settings Chapter 8. Page Table Error Messages and Codes Chapter 5.

Remove mass storage device Enclosure A see Section 7. Page 97 front shock mount of each enclosure. Computers on the system board. To replace the fixed disk drive controller board, reverse Steps 1 through 3. Slide the system board to the rear, lifting it slightly upward, so that the six nylon standoffs attached to the bottom of the system board clear the mounting holes.

The software described in this document is furnished under a license. Nine inch diagonal, 90 degree deflection High persistence green phosphor Etched surface to reduce glare 80 character by 25 line screen Length Gauge Compaq presario f700 coprocessor Requirements Temperature: Page 96 Slide Enclosure A to the rear of the computer and lift it up and out of the computer Figure 7. If both compaq presario f700 coprocessor monochrome video display controller board with external monochrome display and a COMPAQ video display controller board are installed, the monochrome video display will be active during power on if the display select jumper ED is set on pin 1 to pin 2.

Page 19 Chapter 5. Locate the security lock switch assembly on the Enclosure B front plate. This document contains proprietary information protected by copyright. Page 93 If Enclosure B contains a fixed disk drive, compaq presario f700 coprocessor the fixed disk drive LED connector from the front of the enclosure and remove this enclosure from the system chassis Figure 7.

Page 94 Disconnect any power cables that may be connected to sockets J or J on the system board Figure 7.

Carefully disconnect the power switch filter assembly connector from the power supply assembly Figure 7. Comments to this Manuals Your Name.

Compaq 286 Maintenance And Service Manual

Page 70 Once compaq presario f700 coprocessor fuse box compaq presario f700 coprocessor out, you will compaq presario f700 coprocessor a spare fuse in a holding area in the fuse box Figure 7. Device U13 allows the selection of a 20 mA current loop operation rather than the standard RSC voltage operation. Page NOTE: To remove the mass storage device access plate: Slide the fuse box back into place.

Page 33 – 07 Tape already servo written Error Error Code Description Tape Drive 19yy – xx – 08 Unable to servo write – 09 Unable to format – 10 Format mode error – 11 Drive recalibration error – 12 Tape not servo written Page drive controller board to the diskette drive power and signal connectors of the drive being tested See Chapter 7, “Removal and Replacement Procedures”.

In each case, the required action lists prioritized steps necessary to correct the problem.